Working Videos of Wuxi JACK 

CNC Pipe Cutting Machine

Navigation Bar on “Working Videos of CNC Pipe Cutting Machine”

Purpose of This Page on Flame and Plasma CNC Pipe Intersection Cutting Machine

Running Videos of Wuxi JACK CNC Pipe Cut Machine

1. Video 1: Panoramic View on Customer Working Site of Wuxi JACK 7 Axis CNC Pipe Cut Machine:

1) Background: This video was taken at customer facility: A petrochemical plant situated at Texas USA. A set of Wuxi JACK produced CNC-CP-7-3000/12 model 7 Axis Large CNC Pipe Cutting Machine was ready to work;
2) Workpiece: You can find a piece of Φ3000mm large tank being laid on friction roller group, and will be cut and beveled in the CNC Pipe Intersection Cutting Machine.

2. Video 2: Hand Held Torch Piercing Hole into 100mm Thickness Wall Pipe in Flame Plasma CNC Pipe Cutting Machine:

1) Pipe Thickness: As can be observed from the video, the large pipe to be cut in CNC Pipe Intersection Cutting Machine has 100mm thickness wall;
2) Pierce Necessary: The 100mm thickness wall pipe needs to have hole pierced and cut lead in line, before official automatic flame cutting in the CNC Pipe Cut Machine;
3) Pierce Operation: The thick wall hole piercing should be made by hand. As shown in the video, to have safe operation, operator of the CNC Pipe Cutting Machine should put on proper PPE (Personal protective equipment): Helmet and glove, hard shoes.

3. Managing on Operation of CNC-CP-7-3000/12 Model 7 Axis Large Flame CNC Pipe Intersection Cutting Machine:

Video 3: Start on and Have Flame Cutting in 7 Axis Large CNC Pipe Cut Machine:

Video 4: Oxygen Flame Cutting in Large Tank with 7 Axis Large CNC Pipe Cutting Machine:

Video 5: Short Distance Check on Flame Cutting on Large Tank with 7 Axis Large CNC Pipe Cut Machine:

1) Background: This video was taken at customer facility. At the initiation, flame cutting torch mechanism moves and positions on correct cutting point on the large pipe, which was laid on friction roller support of the CNC Pipe Cutting Machine;

2) Operating Passage: For cutting on Φ3000mm diameter large tank, operators need to stand on an aerial passage, which is installed alongside the large CNC Pipe Intersection Cutting Machine;

3) Checking Closely: There is a segment of extending passage installed overhead the CNC Pipe Cut Machine, so that operators can access and stand onto the large pipe, and observe on cutting torch at close distance;

4) Start on Cutting: At the initiation of flame cutting, the cutting torch moves and positions to start point; Then, with automatic ignition, flame cutting begun in the large CNC Pipe Cut Machine.

1) Background: This video reflects on flame cutting in Wuxi JACK 7 Axis large CNC Pipe Intersection Cutting Machine, by means of cutting on a piece of Φ3000mm large tank, at customer workshop;
2) Cutting Speed: Because of large thickness (100mm) of the carbon steel tank, the flame cutting speed in the large CNC Pipe Cut Machine was fairly slow: Around 200mm/min.;
3) 7 Axis CNC Control: To have successful hole cutting, the cutting torch need to be swinged along tank axial and radius direction, which are A and B axis of the 7 Axis large CNC Pipe Cut Machine;
4) Operator Status: As can be observed from the video, operator of this large CNC Pipe Cutting Machine does not have toilful job: Just stand by and check on cutting condition, and have an adjustment when necessary.
 

1) Background: In this video, to have more clear view on cutting point, the 2 working staff climbed onto top of the Φ3000mm large tank, which is laid on friction roller group of the large CNC Pipe Cutting Machine;
2) 7 Axis CNC Control: You can have a more closer view on the 7 axis controlled cutting torch of this large CNC Pipe Intersection Cutting Machine. During operation period, working staff should pay attention to their safety as priority.

Video 6: Vertical View on Operating Site of Wuxi JACK CNC-CP-7-3000/12 Model 7 Axis Large CNC Pipe Cut Machine:

1) Background: This video was taken from high angle, and operating side of the large CNC Pipe Cutting Machine. From it you can have a general idea on working site of the Flame Plasma CNC Pipe Intersection Cutting Machine: The overhead long passage, the in the air operating station, and cutting torch mechanism of the CNC Pipe Intersection Cutting Machine;
2) On Site Layout: Standing at the 3.5m height overhead platform, operator of the CNC Pipe Cut Machine can have a head up vision on large diameter tank cutting process clearly. Which is, not only get the best angle view of observation, but also with good ergonomics condition;
3) Convenient and Intuitive Operation: Operator operates on the 7 axis large CNC Pipe Cutting Machine by means of the industrial level CNC computer at hand. All the working steps are available for management in this advanced control station of the CNC Pipe Cut Machine.

4. Commissioning on Wuxi JACK CNC Pipe Cut Machine:

Video 7: Idle Flame Cutting Torch of Wuxi JACK CNC Pipe Cutting Machine:

1) This short video was taken during commissioning on CNC Pipe Intersection Cutting Machine at Wuxi JACK workshop;
2) You can find tongue of flames being ejected from its Oxygen fuel cutting torch. This is for validating on the normal condition of cutting torch before official cutting in the CNC Pipe Cut Machine.

Video 8: Trial Run on Oxygen Flame Cutting in Large Pipe with 7 Axis CNC Pipe Intersection Cutting Machine:

1) Background: This video was taken during installing and commissioning on the CNC-CP-7-3000/12 model 7 Axis large CNC Pipe Cut Machine. To test on its performance, a piece of Φ2000mm diameter large pipe was being cut with oxygen flame;
2) Cutting Torch Unit: From the video, you can check the cutting torch mechanism of the large CNC Pipe Cutting Machine. And, operator needs to climb onto a ladder to get access on cutting point of the CNC Pipe Intersection Cutting Machine.

Video 9: Large Pipe Flame Cutting in CNC Pipe Intersection Cutting Machine:

In this video, a piece of large pipe was being cutting holes in 7 Axis large CNC Pipe Cutting Machine. There are several holes of different diameters in the pipe, which have been cut with Oxygen fuel torch mechanism, in the CNC Pipe Cut Machine

5. Flame and Plasma Cutting Operation in CNC-CP Series CNC Pipe Cutting Machine:

Video 10: Oxygen Fuel Flame Cutting in Large Pipe with 7 Axis large CNC Pipe Cut Machine:

Video 11: Flame Cutting Torch Ignition and Hole Piercing in Wuxi JACK Large CNC Pipe Cutting Machine:

1) Background: This 4 and half minutes video in detail records on the flame cutting operation, on a piece of Φ3000mm large diameter pipe, in 7 Axis Flame CNC Pipe Intersection Cutting Machine;
2) What For: The flame cutting mainly focus on hole cutting in pipe, and 7 axis control cutting torch mechanism of the CNC Pipe Cutting Machine.

1) Background: This minute video records on cutting torch ignition and hole cutting operation in Wuxi JACK 7 axis flame large CNC Pipe Cut Machine: How does the torch ignited, and swing along 360° directions under the control of A/ B /V axis, in the test run of the 7 axis CNC Pipe Intersection Cutting Machine;
2) Motion: You can find for hole piercing purpose, the cutting torch keeps on still for long certain during the period.

6. Finished Cut Pipe Produced from 5/ 6 /7 Axis Flame Large CNC Pipe Cutting Machine:

Video 12: Flame Cut Lead In Line in Large Pipe with 7 Axis CNC Pipe Intersection Cutting Machine:

Video 13: Finished Hole and Slant Bevel Cut from Wuxi JACK CNC Pipe Cutting Machine:

Other series of Products We Own besides CNC Pipe Cutting Machine

CNC Pipe Cutting Machine Blogs