1. The 5 Axis 600/12 model flame and plasma profile cutting on pipe, is the No.1 selected model, among all the models of 600mm specification group of CNC Pipe Cutting Machine, for cutting and chamfering on small sizes of tubes, up to Φ600mm diameter;
2. Here the model of “600/12” has the longest valid cutting stroke along pipe longitudinal direction, up to 12m;
3. Besides, with the 4th (A axis) and 5th (B axis) control axis for cutting torch swinging along longitudinal and axial direction, this 5 axis CNC machine can cut out chamfering on pipe edge and intermediate body, into bevels of various required profile;
4. Below is the picture taken on typical finished small pipes, with various types of slant bevel edge, cut from Wuxi JACK 5 Axis 600/12 Plasma Flame CNC Pipe Cutting Machine: (Fig.1)
This machine composes three systems of:
1) Checking from the above photo, for the branch of 600mm specification machine, the pipe clamping and securing unit is of 3 claw chuck type, with several sets of bracket support rollers along its lengthways direction;
2) 3 claw chucks applied in 600mm grade of plasma and flame CNC pipe cutting: (Fig.3)
1) No matter small size grade 600mm of this product section, or middle size grade 1400mm machine, together with large size grade 3000mm machine, the cutting systems are the same:
a) Oxygen fuel cutting torch for performing flame cutting on carbon steel, of small to medium to large thickness;
b) And or plasma cutting torch unit for non-ferrous material, of small to medium thickness;
c) Cutting torch and gas tubes traveling system, along the entire length of machine;
1) Shown in the above photo, control system of all the models of CNC-CP series machine is adopted with industrial computer;
2) This industrial computer belongs to workstation of table or pendant type, depending on specific design on mechanical system;
3) Its software of operating system, hardware of control circuit and monitor are all specially for CNC control pipe cutting operation;
4. Summing up, the above introduced 3 systems: The chuck fixture, supporting rollers and cutting torch traveling system are integrated into an integral group, guaranteeing reliable and accurate operation of this advanced technology 5 axis machine on CNC pipe profile cutting.
1) Below picture shows the pipe cut into 60×120 ellipse in the machine: (Fig.5)
2) For the purpose of precise cutting and beveling operation, there are 2 sets of pipe ovality detection system, which are installed at both sides of the cutting torch unit, along pipe lengthways (axial) direction;
3) The manufacture on grooving system has mature technology, which features in ingenious structure, little clearance and high precision;
1) As can be observed from the above small photo, the professional workpiece library built in the CNC industrial computer of the CNC Pipe Cutting Machine is simple and easy to use;
2) The groove for later on welding can be cut together with cutting, without the need of follow up machining, accurate and efficient;
3) In all, the 5 Axis Profile Cutting Machine is very appropriate for customers, whose pipe and tube are small size and need various kinds of processing for next step of welding and or assembly.
Model Technical Parameter | 5 Axis CNC-CP 600/12 Profile Plasma Flame CNC Pipe Intersection Cutting Machine |
Diameter Range of Workpiece Pipe for Cutting and Groove | 80 ~ 600 mm |
Max. Length of Workpiece Pipe for Cutting and Groove | 12,000 mm |
Thickness of Workpiece Pipe for Cutting and Groove | 6~100 mm for flame cutting; 3 ~ 25mm for plasma cutting |
Cutting Speed for Cutting and Groove | 200∼800mm/min. for flame cutting Around 200~ 2000mm/min. for plasma cutting (Based on thickness of Pipe and Plasma Power) |
CNC Control Axis | 5 Axis of X/ Y/ Z/ A/ B: A: Cutting torch swing along pipe length; B: Cutting torch swing along pipe radius; X: Cutting Torch Move along pipe length; Y: Cutting Torch Move along pipe radius; Z: Cutting Torch elevation |