Availability: | |
---|---|
Quantity: | |
1. Characteristic: The master photo of this product section reflects assembling moment of the Plate Edge Chamfering Machine: 2 assemblers were working at both sides of the working table, face to face;
2. It is also true during official running of this special design Plate Edge Grooving Machine, that 2 pieces of milling head will work at both sides of workpiece, make edge milling face to face at the same time. Shown as below:
1) Perform double sides edge milling on strip steel plates with one time stroke operation. In that case, the width of steel plate applicable for the Edge Milling Machine is in the range of 300mm to 1000mm. Shown as below:
2) Same as standard Plate Edge Chamfering Machine, fulfil edge grooving on single side of steel plates. By this time, only one set of milling head is in working, the other side milling head waits in idle status;
The distinguished merit of such special design Large Plate Edge Milling Machine can be summarized as high efficiency and easy operation, especially for those workpieces which need both side of edge grooving. Let us assume 2 conditions as below:
1. For steel plates equal to or narrower than 1000mm, it can be edge milled both sides in this Special Plate Edge Milling Machine directly, with one time operation;
1) Although it can not be machined at both sides simultaneously in this Edge Milling Machine, operator can finish one side edge milling first;
2) Then, without taking off the steel plate from Edge Milling Machine, make adjustment on longitudinal position of the steel plate, by just pulling and pushing the steel plate in the direction perpendicular to horizontal worktable of the Edge Milling Machine;
3) Then, start on milling head at the opposing side of Plate Edge Chamfering Machine worktable;
4) Comparatively, in conventional standard Plate Edge Milling Machine, operator need to take off the steel plate, and flip it 180°, then load the steel plate into the Plate Edge Grooving Machine the second time.
Although this Special Edge Milling Machine basically works in the same style as remaining standard Edge Chamfering Machine, it does have its unique operation noting point, which can be listed as below two main points of:
1) Although this is a double heads Plate Edge Grooving Machine, its two sets of milling heads are distributed at both sides of the worktable. So, the milling head can only perform straight and upper beveling. In this sense, it works like a set of single head plate Edge Milling Machine;
2) When it is necessary to have lower edge beveling on steel plate, just like the operation in standard single head plate Edge Milling Machine: Take off the steel plate, then overturn it 180°, then load the steel plate into the Plate Edge Chamfering Machine again for the second time grooving;
3) This is the reason that, when customer decide to choose between this type of Special Plate Edge Milling Machine and standard Edge Milling Machine, they should not only consider the demand on steel plates both sides grooving, but also types of grooving on each side of workpiece;
1) In standard Plate Edge Grooving Machine, it does not exist the problem of steel plate conflicting with milling head. Because material loading in and milling head operation happen at different side of Edge Milling Machine;
2) Comparatively, in this special design Plate Edge Chamfering Machine, both sides of worktable can be material handling and milling operation. So, before steel plate loading in and off the Edge Milling Machine, operator need to drive the milling heads to extreme position first, leaving sufficient spatial space for material handling.
Model Technical parameter | SXBJ-12 Face to Face Milling Large Plate Edge Milling Machine |
Max. Plate Beveling Length (mm) | 12,000 |
Power and rpm of Milling Head | 7.5 kW, 1440 rpm |
Spindle rpm of Edge Milling Head | 75 ~ 420 r/min., 6 grades by handwheel |
Hydraulic Power Motor | 5.5 kW |
Milling Head Quantity and Installation | 2 sets, installed face to face |
Plate thickness for Sheet Metal chamfering | 6 ∼ 50 mm |
Edge Milling Speed | 130∼1000 mm/min. (VFD, Inverter Control) |
High Speed of Idle | 4000 mm/min. |
Applicable Diameter of Facer Plate | D=Ø125 ~ Ø320mm (Ø200 For delivery) |
Hydraulic Rated Pressure | 5.5 MPa |
Hydraulic Working Pressure | 3.5 MPa |
Hydraulic System Flowrate | 47 L/min. |
Worktable Width | 450 mm |
Worktable Height | 1050 mm |
1. Characteristic: The master photo of this product section reflects assembling moment of the Plate Edge Chamfering Machine: 2 assemblers were working at both sides of the working table, face to face;
2. It is also true during official running of this special design Plate Edge Grooving Machine, that 2 pieces of milling head will work at both sides of workpiece, make edge milling face to face at the same time. Shown as below:
1) Perform double sides edge milling on strip steel plates with one time stroke operation. In that case, the width of steel plate applicable for the Edge Milling Machine is in the range of 300mm to 1000mm. Shown as below:
2) Same as standard Plate Edge Chamfering Machine, fulfil edge grooving on single side of steel plates. By this time, only one set of milling head is in working, the other side milling head waits in idle status;
The distinguished merit of such special design Large Plate Edge Milling Machine can be summarized as high efficiency and easy operation, especially for those workpieces which need both side of edge grooving. Let us assume 2 conditions as below:
1. For steel plates equal to or narrower than 1000mm, it can be edge milled both sides in this Special Plate Edge Milling Machine directly, with one time operation;
1) Although it can not be machined at both sides simultaneously in this Edge Milling Machine, operator can finish one side edge milling first;
2) Then, without taking off the steel plate from Edge Milling Machine, make adjustment on longitudinal position of the steel plate, by just pulling and pushing the steel plate in the direction perpendicular to horizontal worktable of the Edge Milling Machine;
3) Then, start on milling head at the opposing side of Plate Edge Chamfering Machine worktable;
4) Comparatively, in conventional standard Plate Edge Milling Machine, operator need to take off the steel plate, and flip it 180°, then load the steel plate into the Plate Edge Grooving Machine the second time.
Although this Special Edge Milling Machine basically works in the same style as remaining standard Edge Chamfering Machine, it does have its unique operation noting point, which can be listed as below two main points of:
1) Although this is a double heads Plate Edge Grooving Machine, its two sets of milling heads are distributed at both sides of the worktable. So, the milling head can only perform straight and upper beveling. In this sense, it works like a set of single head plate Edge Milling Machine;
2) When it is necessary to have lower edge beveling on steel plate, just like the operation in standard single head plate Edge Milling Machine: Take off the steel plate, then overturn it 180°, then load the steel plate into the Plate Edge Chamfering Machine again for the second time grooving;
3) This is the reason that, when customer decide to choose between this type of Special Plate Edge Milling Machine and standard Edge Milling Machine, they should not only consider the demand on steel plates both sides grooving, but also types of grooving on each side of workpiece;
1) In standard Plate Edge Grooving Machine, it does not exist the problem of steel plate conflicting with milling head. Because material loading in and milling head operation happen at different side of Edge Milling Machine;
2) Comparatively, in this special design Plate Edge Chamfering Machine, both sides of worktable can be material handling and milling operation. So, before steel plate loading in and off the Edge Milling Machine, operator need to drive the milling heads to extreme position first, leaving sufficient spatial space for material handling.
Model Technical parameter | SXBJ-12 Face to Face Milling Large Plate Edge Milling Machine |
Max. Plate Beveling Length (mm) | 12,000 |
Power and rpm of Milling Head | 7.5 kW, 1440 rpm |
Spindle rpm of Edge Milling Head | 75 ~ 420 r/min., 6 grades by handwheel |
Hydraulic Power Motor | 5.5 kW |
Milling Head Quantity and Installation | 2 sets, installed face to face |
Plate thickness for Sheet Metal chamfering | 6 ∼ 50 mm |
Edge Milling Speed | 130∼1000 mm/min. (VFD, Inverter Control) |
High Speed of Idle | 4000 mm/min. |
Applicable Diameter of Facer Plate | D=Ø125 ~ Ø320mm (Ø200 For delivery) |
Hydraulic Rated Pressure | 5.5 MPa |
Hydraulic Working Pressure | 3.5 MPa |
Hydraulic System Flowrate | 47 L/min. |
Worktable Width | 450 mm |
Worktable Height | 1050 mm |