Availability: | |
---|---|
Quantity: | |
1) As can be observed from the attached first photo and below, viewing from visual angle of photographer, milling units are installed at the right side of Edge Milling Machine mechanical main frame, while left side is bracket group for workpiece loading in and out of the Edge Beveling Machine;
1) This is the mainstream structure of XBJ and XBJ series Edge Milling Machine, that the front side of its mechanical main frame is material handling side, and the back side is for performing edge milling operation;
2) If you check the above photo carefully, you may find that lateral view on cross section of such one side acting Edge Milling Machine, it’s mechanical pedestal is in the shape of “L”, catering for installation and operation requirement on the End Beveling Machine;
3) Comparatively, there is another kind of double side acting SXBJ-12 Sheet Metal Plate End Chamfering Machine, that both sides of mechanical main frame are installed with milling heads. The corresponding mechanical frame of the Edge Milling Machine is also different:
5) As can be found from the above photo, the mechanical base bed of double side acting End Beveling Machine is the form of “┷”, which is for the purpose of symmetrical structure on both sides installing and running milling unit;
1) As mentioned previously, this is the main stream and default structure of Edge Chamfering Equipment Edge Milling Machine;
2) Which means, when there is no special demand from customers, we design and produce such kind of one side acting End Chamfering Machine;
3) Such structure of Edge Beveling Machine can meet most majority of customer demand, and takes over 90% share of Edge Milling Machine practical application.
Let us make analysis on front side and back side of the Edge Milling Machine respectively:
1) This side composes of array of standing brackets, serving as steel plates loading into and unloading out of the Edge Chamfering Equipment;
3) The above photo demonstrates the traditional way and structure of material holding brackets adopted in Edge Milling Machine, which is also the common practice adopted in industry;
a) Downside of such brackets is, the pushing in and pulling out steel plates into and out of End Chamfering Machine is fairly uneasy and even dangerous, especially for large and heavy steel plates into and out of the Edge Milling Machine;
b) For example, suppose a piece of 12m length, 50mm thickness, and 2500mm width steel plate will be edge milled in the Edge Milling Machine. By calculation, its total weight will be 12 Ton, very hard job for operators of End Beveling Machine for its handling;
5) To solve this problem for customers, Wuxi JACK successfully develops a kind of solitary owned hydraulic driving automatic steel plate handling system, which completely solve the above difficulty for customers of Edge Milling Machine:
1) In Edge Milling Machine, each set of milling head is installed onto a set of moving carriage, which moves along working table of the End Chamfering Machine, fulfilling edge milling operation;
2) In Edge Milling Machine, on each set of moving carriage, besides milling head and its horizontal movement driving motor, there are also series of important components and assemblies: Driving motor for milling head up and down, sector gear, feeding and retreating modulation transmission and handwheel of milling head in Edge Milling Machine, electric control board and operating pendant, as well as milling head tilting mechanism, angular ruler.... All of these elements and mechanisms form up the position and action control of milling head, before grooving operation of the Edge Milling Machine;
4) As can be found from the above photo, the 2 sets of milling heads in the End Beveling Machine have different assembling orientation: The left one is for making bottom edge beveling of Edge Milling Machine, and the right one is for making side and up edge beveling.
Below are technical specifications of the SXBJ-12 Sheet Metal Plate End Beveling Machine:
Model Technical parameter | SXBJ-12 Double Heads One Side Acting Sheet Metal Plate Edge Beveling Machine |
Max. Plate Beveling Length | 12,000 mm |
Power and rpm of Milling Head | 7.5 kW, 1440 rpm |
Spindle rpm of Edge Milling Head | 75 ~ 420 r/min., 6 grades by handwheel |
Hydraulic Power Motor | 5.5 kW |
Milling Head Quantity | 2 sets |
Plate thickness for Sheet Metal chamfering | 6∼50 mm |
Milling Angle of Top Milling unit | 0° to +80° |
Milling Angle of Down Milling unit | -60° to 0° |
Edge Milling Speed | 130∼1000 mm/min. (VFD, Inverter Control) |
High Speed of Idle | 4000 mm/min. |
Applicable Diameter of Facer Plate | D=Ø125 ~ Ø320mm (Ø200 For delivery) |
Quantity of Hydraulic Jacks | 20 pieces |
Hydraulic Rated Pressure | 5.5 MPa |
Hydraulic Working Pressure | 3.5 MPa |
Hydraulic System Flowrate | 47 L/min. |
Worktable Width | 450 mm |
1) As can be observed from the attached first photo and below, viewing from visual angle of photographer, milling units are installed at the right side of Edge Milling Machine mechanical main frame, while left side is bracket group for workpiece loading in and out of the Edge Beveling Machine;
1) This is the mainstream structure of XBJ and XBJ series Edge Milling Machine, that the front side of its mechanical main frame is material handling side, and the back side is for performing edge milling operation;
2) If you check the above photo carefully, you may find that lateral view on cross section of such one side acting Edge Milling Machine, it’s mechanical pedestal is in the shape of “L”, catering for installation and operation requirement on the End Beveling Machine;
3) Comparatively, there is another kind of double side acting SXBJ-12 Sheet Metal Plate End Chamfering Machine, that both sides of mechanical main frame are installed with milling heads. The corresponding mechanical frame of the Edge Milling Machine is also different:
5) As can be found from the above photo, the mechanical base bed of double side acting End Beveling Machine is the form of “┷”, which is for the purpose of symmetrical structure on both sides installing and running milling unit;
1) As mentioned previously, this is the main stream and default structure of Edge Chamfering Equipment Edge Milling Machine;
2) Which means, when there is no special demand from customers, we design and produce such kind of one side acting End Chamfering Machine;
3) Such structure of Edge Beveling Machine can meet most majority of customer demand, and takes over 90% share of Edge Milling Machine practical application.
Let us make analysis on front side and back side of the Edge Milling Machine respectively:
1) This side composes of array of standing brackets, serving as steel plates loading into and unloading out of the Edge Chamfering Equipment;
3) The above photo demonstrates the traditional way and structure of material holding brackets adopted in Edge Milling Machine, which is also the common practice adopted in industry;
a) Downside of such brackets is, the pushing in and pulling out steel plates into and out of End Chamfering Machine is fairly uneasy and even dangerous, especially for large and heavy steel plates into and out of the Edge Milling Machine;
b) For example, suppose a piece of 12m length, 50mm thickness, and 2500mm width steel plate will be edge milled in the Edge Milling Machine. By calculation, its total weight will be 12 Ton, very hard job for operators of End Beveling Machine for its handling;
5) To solve this problem for customers, Wuxi JACK successfully develops a kind of solitary owned hydraulic driving automatic steel plate handling system, which completely solve the above difficulty for customers of Edge Milling Machine:
1) In Edge Milling Machine, each set of milling head is installed onto a set of moving carriage, which moves along working table of the End Chamfering Machine, fulfilling edge milling operation;
2) In Edge Milling Machine, on each set of moving carriage, besides milling head and its horizontal movement driving motor, there are also series of important components and assemblies: Driving motor for milling head up and down, sector gear, feeding and retreating modulation transmission and handwheel of milling head in Edge Milling Machine, electric control board and operating pendant, as well as milling head tilting mechanism, angular ruler.... All of these elements and mechanisms form up the position and action control of milling head, before grooving operation of the Edge Milling Machine;
4) As can be found from the above photo, the 2 sets of milling heads in the End Beveling Machine have different assembling orientation: The left one is for making bottom edge beveling of Edge Milling Machine, and the right one is for making side and up edge beveling.
Below are technical specifications of the SXBJ-12 Sheet Metal Plate End Beveling Machine:
Model Technical parameter | SXBJ-12 Double Heads One Side Acting Sheet Metal Plate Edge Beveling Machine |
Max. Plate Beveling Length | 12,000 mm |
Power and rpm of Milling Head | 7.5 kW, 1440 rpm |
Spindle rpm of Edge Milling Head | 75 ~ 420 r/min., 6 grades by handwheel |
Hydraulic Power Motor | 5.5 kW |
Milling Head Quantity | 2 sets |
Plate thickness for Sheet Metal chamfering | 6∼50 mm |
Milling Angle of Top Milling unit | 0° to +80° |
Milling Angle of Down Milling unit | -60° to 0° |
Edge Milling Speed | 130∼1000 mm/min. (VFD, Inverter Control) |
High Speed of Idle | 4000 mm/min. |
Applicable Diameter of Facer Plate | D=Ø125 ~ Ø320mm (Ø200 For delivery) |
Quantity of Hydraulic Jacks | 20 pieces |
Hydraulic Rated Pressure | 5.5 MPa |
Hydraulic Working Pressure | 3.5 MPa |
Hydraulic System Flowrate | 47 L/min. |
Worktable Width | 450 mm |